Contents:
Installation Instruction for version TA-079 Verify PCB Version it is suggested to remove solder-mask first (see part 2) Glue FPC cable Solder the wires (30 AWG) to the FPC. V33 GND CLK Solder the wires (30 AWG for GND and V25) to the FPC). Press firmly on the installation aid and remove the soldermask using a sharp tool. Solder the wires from the solder points to the FPC. (A to H from top to bottom).Cut PCB trace under the yellow spot (6th line from top). Remove the soldermask under the red spots. Solder the wires from the solder points to the FPC. BTN1 BTN2 Solder the wires from the solder points to the FPC. Put some tape on the back to avoid Continue to download »
Sponsored Links
Installation Instruction for version TA-079 Verify PCB Version it is suggested to remove solder-mask first (see part 2) Glue FPC cable Solder the wires (30 AWG) to the FPC. V33 GND CLK Solder the wires (30 AWG for GND and V25) to the FPC). Press firmly on the installation aid and remove the soldermask using a sharp tool. Solder the wires from the solder points to the FPC. (A to H from top to bottom).Cut PCB trace under the yellow spot (6th line from top). Remove the soldermask under the red spots. Solder the wires from the solder points to the FPC. BTN1 BTN2 Solder the wires from the solder points to the FPC. Put some tape on the back to avoid direct contact with the MS Slot. Installation instructions for version TA-081 PART 1/3. Verify PCB version it is suggested to remove soldermask first (see part 2) Glue FPC cable V33 GND (alternative) GND Solder the wires (30 AWG) to the FPC. V25 CLK Solder the wires (30 AWG for V25) to the FPC. Press firmly on the installation aid and remove the soldermask using a sharp tool. 
Installation Guidelines Precautions 1 Installation is for skilled professionals ONLY and should not be attempted by amateurs 2 Removal of the soldermask is the most difficult and hazardous part of the installation and requires the most patience 3 The PSP motherboard contains highly condensed traces and components which means a visual aid such as a microscope or magnifying glass will be required We recommend the use of a video or optical microscope Guidelines 1 The stencils are used to assist with the process of removing the soldermask from the motherboard PCB This is done by first fixing the stencil in place as shown by the installation diagrams and then scratching the soldermask off the PCB with a sharp tool using the edge of the stencil as a guide This is the most hazardous part of the installation since it is possible to cause permanent damage to the PCB traces during this procedure Great care must be taken not to apply too much pressure whilst removing the soldermask otherwise the traces can be damaged or even severed Secure the stencil in place with hot 
Note before you open your PSP make sure that UP modchip is compatible with your PSP version Se next page how to se PSP version Guide how to open a psp se this link http www console se download psp up OpenyourPSP pdf What you need UP Undiluted Platinum modchip Solder station with smal tip maximum 0 25 mm Flux Thin razor blade Low temp glue gun Multimeter Undiluted Platinum flasher http www console se download psp up UndilutedPlatinumSetup zip On next page we have inserted the official installation diagrams after that we have added helpfull tips from our proffesional installers at www console se and www divineo se Also thanx for all tips from users ww maxconsole net Precautions This installation is extremly hard it s possible that you damage your PSP if you do anything wrong The typical with the installation is that you must solder directly to small traces the traces are protected with a grean coating called soldermask First thing you must do is to remove the soldermask 1 Installation is for skilled professionals ONLY and should not be 
