Contents:
Installation Instruction for version TA-079 Verify PCB Version it is suggested to remove solder-mask first (see part 2) Glue FPC cable Solder the wires (30 AWG) to the FPC. V33 GND CLK Solder the wires (30 AWG for GND and V25) to the FPC). Press firmly on the installation aid and remove the soldermask using a sharp tool. Solder the wires from the solder points to the FPC. (A to H from top to bottom).Cut PCB trace under the yellow spot (6th line from top). Remove the soldermask under the red spots. Solder the wires from the solder points to the FPC. BTN1 BTN2 Solder the wires from the solder points to the FPC. Put some tape on the back to avoid direct contact with the MS Slot. Installation instructions for version TA-081 PART 1/3. Verify PCB version it is suggested to remove soldermask first (see part 2) Glue FPC cable V33 GND (alternative) GND Solder the wires (30 AWG) to the FPC. V25 CLK Solder the wires (30 AWG for V25) to the FPC. Press firmly on the installation aid and remove the soldermask using a sharp tool. Continue to download »
Sponsored Links
Installation Guidelines Precautions 1 Installation is for skilled professionals ONLY and should not be attempted by amateurs 2 Removal of the soldermask is the most difficult and hazardous part of the installation and requires the most patience 3 The PSP motherboard contains highly condensed traces and components which means a visual aid such as a microscope or magnifying glass will be required We recommend the use of a video or optical microscope Guidelines 1 The stencils are used to assist with the process of removing the soldermask from the motherboard PCB This is done by first fixing the stencil in place as shown by the installation diagrams and then scratching the soldermask off the PCB with a sharp tool using the edge of the stencil as a guide This is the most hazardous part of the installation since it is possible to cause permanent damage to the PCB traces during this procedure Great care must be taken not to apply too much pressure whilst removing the soldermask otherwise the traces can be damaged or even severed Secure the stencil in place with hot 
Nokia Car Kit CK 300 User and Installation Guide 9202247 Issue 1 EN DECLARATION OF CONFORMITY Hereby NOKIA CORPORATION declares that this HF 21W product is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The product is in conformity with the limits defined in Directive 2004 104 EC amending Directive 72 245 EEC Annex I paragraph 6 5 6 6 6 8 and 6 9 A copy of the Declaration of Conformity can be found at http www nokia com phones declaration of conformity 0434 2008 Nokia All rights reserved Reproduction transfer distribution or storage of part or all of the contents of this document in any form without the prior written permission of Nokia is prohibited Nokia Nokia Connecting People and Navi are trademarks or registered trademarks of Nokia Corporation Other product and company names mentioned herein may be trademarks or tradenames of their respective owners Bluetooth is a registered trademark of Bluetooth SIG Inc Nokia operates a policy of ongoing development Nokia 
Additional Installation time may be necessary for installation of 6-Disc CD Changer together with Satellite Radio, please refer to page 4. The instructions below are developed for BMW vehicles and are not be compared to any other existing instructions for vehicles other than BMW. No methods other than those specified in this document are to be used for installation in BMW vehicles. Left and right are determined from driver’s seat. Carefully read all instructions and supplements before proceeding with the installation. Reference should be made to TIS for instructions dealing with a stock part of the vehicle but not stated in detail in these instructions. The instructions were complete and up to date at time of publication; however, changes to the vehicle or installation may have occurred. Please report any problems or changes noted with the installation to BMW Technical Hotline, along with VIN, date of manufacture and as much detail as possible. PARTS INFORMATION Contents of Kit – P/N 84 11 0 390 240 Description Sirius Bracket ALC Module 
Introduction Safety Information Tools Needed Overview Hardware Components Installation Step 1 Step 2: Step 3: Step 4: Step 5: Assemble Third Brake Light Mount The Third Brake Light Route the Wires Make the Electrical Connections Install the Fuse Holder And Fuse Removing Third Brake Light Trouble Shooting Replacement parts guide Limited Warranty INTRODUCTION Thank you for purchasing a Logo Lites® LED Third Brake Light Kit. Your third brake light kit was built to high quality standards to provide you with years of reliable service. This manual should serve as a guide for installing a third brake light kit on your vehicle. Although this guide is thorough, each installation is different, so it can not cover all applications. You can install the turn signal kit yourself IF: 1. you have the right tools, 2. you have a reasonable mechanical and electrical aptitude or experience, 3. you have the knowledge or diagrams of where wiring, fuel lines, etc. are located in the vehicle, 4. and you read and follow the instructions very carefully. SAFETY INFORMATION Read 
